We Checkline Europe Ltd would like to use cookies and similar technologies in order to optimize your shopping experience and this requires your consent. By clicking on the "Accept cookies" button you agree to our use of cookies and similar technologies. If you do not agree, you can refuse the use or customize settings for the respective cookies by clicking on the button "Cookie Settings".You also have the possibility to specify that only certain cookies, which we use on our website should be activated. This banner will be displayed until you have selected your cookie preferences. If you decide against the use of cookies, we will not use cookies nor similar technologies, except those that are essential for the proper functioning of the website. Click here for our privacy policy
Contact 
Contact Us
Email: info@checkline-europe.co.uk
Your information request is sent!
We'll contact you as soon as possible.

Your message was successfully sent!

PoroTest 7 High voltage porosity detector


Made in GermanyThe PoroTest 7 is available with 3 high voltage probes for different coating thicknesses available (not included):
P7: 0.03 mm – 1.7 mm / 1 mils – 67 mils
P30: 0.52 mm – 9.49 mm / 20.5 mils – 373.6 mils
P35: 1.4 mm – 11.3 mm / 55 mils – 444 mils

Designed for detecting flaws and pores, the PoroTest 7 can be used for non-destructive porosity testing of all insulating coatings on conductive substrates such as steel, aluminium, etc. The test instrument consists of a high voltage probe with an integrated high voltage generator and a test electrode, which is simply connected to the probe. The test voltage control works automatically and is specific to the thickness of the material to be tested and vice versa.

Typical applications of the PoroTest 8 are testing linings and coatings applied on ducts, hulls, pipes, oil and storage tanks, enamel, rubber and bitumen linings, paint, vessels and tanks, GFK and other plastic materials.

The control unit features a digital display and control pad. The control unit housing is fully portable and made of rugged ABS plastic with an integrated handle. The high voltage probe and control unit are connected via a rugged cable. To detect porosity, the appropriate test voltage specific to the material thickness is set on the control unit which applies, when activated, a spark discharge at the moment a material flaw is detected. In addition to the spark discharge, flaws are indicated by a visible and audible signal and counted. The test voltage is directly indicated on the digital display.


Features
  • Powerful and versatile gauge with new ergonomic design making it ideal for on-site testing
  • Backlit display to indicate current test voltage, number of pores and material thickness
  • User-friendly key-pad layout with menu driven operation
  • Residual voltage indicator
  • Variable pre-set test voltages specific to material thickness
  • Alarm signal when exceeding pore limit setting (Limit)
  • High voltage probe with equipment-on and pore indicator (red LED)
  • Power supply: AC operated or battery operated via integrated storage battery (C-cells)
  • Light-weight and hand-held test electrodes provide convenient operation
  • Electrical safety provisions according to VDE 0411, part 1: probe voltage and maximum discharge rate stay below the limit values as specified by the safety standard.
  • Test method conforms to DIN 55 670
  • Low-battery indicator

Test Principle
Move the high voltage search electrode smoothly over the surface. The flaws are detected through spark discharge to the conductive substrate. Test results are shown directly on the digital display.

Test voltage can be adjusted from 500 Volt to 35.000 Volt. The instrument has been designed for testing insulating materials from approx. 30 microns to 11.3 mm (1 mils - 444 mils) thickness.

Specifications
Voltage DC
Display LC-Display, 3-digit
Accuracy of voltage setting ± (0.1 kV + 3% of reading)
Dimensions of high voltage probe 274 mm x 63 mm
Dimension of control unit 225 mm x 150 mm x 85 mm
Weight high voltage probe 550 g
Weight control unit 1400 g
Alarm signal 90 dB, 0.1 s/Pore, continuous tone in case of short-circuit
Signal output potential free, Umax.: 100 V, Imax.: 0.4 A
Storage battery 4 C-cells, IEC LR 14, 3.5 Ah, NiMH, replaceable
Storage battery life at maximum voltage PoroTest 7-P7: 20 hours continious operation
PoroTest 7-P30 & P35: 10 hours continious operation
Storage battery charging time 4 hrs quick charge
Mains voltage 110 to 230 V, 50/60 Hz, automatic switch
Operating temperature 0° - 50°C/ 32°- 122°F
Humidity avoid dew on the surface (refer to DIN 55 670)
Standards DIN EN ISO 2746, DIN 55 670, ASTM D 5162-01, AS 3894.1-2002

360 degree

Downloads

Complete Kit

The PoroTest 7 will be delivered as a complete kit, including:

  • Control unit with integrated storage battery
  • Connecting cable probe-control unit
  • Metal sweeper electrode
  • Power cable
  • Equipotential cable, 5 m (16 ft) length
  • Plastic carrying case
  • Shoulder belt
  • Manual, available in English, German and French

 



Buy Now
Product

Product name
Price
Quantity
PoroTest 7 Porosity Detector
£ 1.765,00 
 
Accessories

Product name
Price
Quantity
P7 - PoroTest P7 High tension electrodes - 0.5 ... 7 kV - 0,03...1,7 mm
£ 1.129,00 
P30 - PoroTest P30 High tension electrodes - 3 ... 30 kV - 0,5...9 mm
£ 1.450,00 
P35 - PoroTest P35 High tension electrodes - 5 ... 35 kV - 1.4...11.3 mm
£ 1.450,00 
Silicon Electrode 200 mm - PoroTest Silicon Electrode 200 mm
£ 110,00 
All mentioned prices are excluding VAT & excluding shipment costs.
Availability : Available , preorder 1-2 weeks , special order, request

Request Information / Quotation




Your information/quotation request is send!


Close



Your message was successfully sent!

Due to technical problems, we are temporarily unavailable by phone. For requests, our head office can be reached under number: +31 53 4356060