We Checkline Europe B.V. would like to use cookies and similar technologies in order to optimize your shopping experience and this requires your consent. By clicking on the "Accept cookies" button you agree to our use of cookies and similar technologies. If you do not agree, you can refuse the use or customize settings for the respective cookies by clicking on the button "Cookie Settings".You also have the possibility to specify that only certain cookies, which we use on our website, should be activated. This banner will be displayed until you have selected your cookie preferences. If you decide against the use of cookies, we will not use cookies nor similar technologies, except those that are essential for the proper functioning of the website. Click here for our privacy policy
Contact 
Contact Us
Email : sales@checkline.eu
Your information request is sent!
We'll contact you as soon as possible.

Your message was successfully sent!

MR06-200 Hand-held Wire Crimp Pull Sensor


Made in the USAThe MR06-200 Wire Crimp Pull Tester is a force sensor designed to make manual field pull testing of crimped wire terminals easy.

This sensor supports a rotary turret with slots for wires from 0,8 mm till 6,4 mm and a load capacity up to 1000 N / 100 KG. The ratcheting mechanism makes it easy to apply up to 1000 N pulling force on the sample.

This force sensor is connected to a Mark-10 Indicator by a Plug & Test® sensor. One of the unique features of the Plug & Test® sensors is that they have their own PCB which stores the calibration and configuration data.
A Plug & Test® sensor can be switched to a different Indicator without the need for calibration or re-configuration.

Once connected and calibrated the MR06-200 is set by rotating the upper grip to an appropriately sized slot (sizes from 0,8mm to 6,3mm) and press the cam shaft button located in the tensioning mechanism. Insert the end of the wire sample in the hole located in the cam shaft. After releasing the cam shaft button the wire is wrapped at least one full rotation clockwise around the cam shaft after which the terminal is inserted in the slot. The sensor is now ready to start testing.

As the MR06-200 is a sensor that needs to be connected to a Series-7i,   Series-5i or  Series-3i indicator(not included) to display the measured force values.

We are happy to assist you in finding the most suitable configuration for your needs. Please contact us for more information.  


Features
  • Ergonomic handles and convenient tensioning mechanism
  • Member of the Plug & Test® family of interchangeable sensors and indicators
  • Compatible with the Series 7i, 5i and 3i digital indicators
  • Measures pull forces
  • NIST-traceable certificate of calibration with data is included. If the sensor is ordered with an indicator, a certificate for the set (indicator + sensor) can be supplied upon request, at no additional charge.
  • Warranty: 3 years

Capacity x Resolution, with Model 7i and 5i Indicators
ModelNkNkgFozFlbF
MR06-2001000 x 0,51 x 0,0005100 x 0,053200 x 2200 x 0.1

Capacity x Resolution, with Model 3i Indicator
ModelNkgFlbF
MR06-2001000 x 1100 x 0,1200 x 0.2

Plug & Test® Smart Force & Torque Sensors

General information

Mark-10 M7I, M5I, and M3I indicators are used in combination with Plug & Test® sensors and can therefore accommodate numerous force and torque measurement requirements, from 1 N to 50 kN (0.25 to 10,000 lbF) of force, and from 7 Ncm to 550 Nm (10 ozFin to 5,000 lbFin) of torque.

Plug & Test® sensors can be used handheld or mounted to a fixture or test stand for more accurate and repeatable testing results.
The sensors are separately calibrated therefore they can be disconnected from one indicator and connected to another without the need for re-calibration or re-configuration as this is stored in the PCB located inside the smart connector.

Accuracy

System accuracy is determined by the combination of Indicator and sensor combined. To determine the total system accuracy the accuracy value of the sensor is added to the value of the indicator.
As the Indicators have different accuracy values the total system accuracy may vary between the different indicator/sensor combinations. Indicator Model Accuracy M7I / M5I ±0,1% of full scale M3I ±0,2% of full scale.

Example 1 Model MR01-100 sensor with Model M5I Indicator MR01-100 ±0,15% of full scale + M5I ±0,1% of full scale = Total ±0,25% of full scale This translates into a fixed error of up to: 0,25% x 500 N = 1,25 N

Example 2 Model MR50-50Z sensor with Model M3I Indicator MR50-50Z ±0,35% of full scale + M3I ±0,2% of full scale = Total ±0,55% of full scale This translates into a fixed error of up to: 0,55% x 50 Ncm = 0,275 Ncm

Because accuracy is defined as a percentage of full scale, the fixed error is possible anywhere on the scale from 0 to the capacity. As such, this value represents an increasingly large error as percentage of reading towards the low end of the scale. It is, therefore, recommended that a sensor is selected with capacity as close as possible to the expected load. The resolution may be different for some sensors depending on whether a M7I, M5I, or M3I indicator is being used. For example, a Series R01 force sensor will display finer resolution when connected to a M5I indicator than when connected to a M3I indicator.


Complete Kit

The Series R06 wire crimp pull sensors are shipped as a complete unit with Plug & Test® sensor.
 



Dimensions
Dimensions-MR06-200


Accessories

Model-3I Force/Torque Indicator


  • Interchangeable force and torque sensors through Plug & Test® technology (sensors are sold separately)
  • High-speed 2.000 Hz sampling rate
  • Large backlit graphic display

More details

Model-3I Force/Torque Indicator 126887

Model-5I Advanced Digital Force/Torque Indicator


  • Interchangeable force and torque sensors through, separately sold, Plug & Test® technology
  • Password protection for individual keys and calibration
  • Sensor password protection, for preventing use of an unauthorized sensor

More details

Model-5I Advanced Digital Force/Torque Indicator 126888

Model-7i Advanced Force/Torque Indicator


  • Interchangeable force and torque sensors through Plug & Test® technology (sensors are sold separately)
  • Sensor password protection, for preventing use of an unauthorized sensor
  • Password protection for individual keys and calibration

More details

Model-7i Advanced Force/Torque Indicator 127113

Specifications
Accuracy±0.5% of full scale
Safe overload150% of full scale ( Indicator display shows “OVER” at 110% and above)
Operating temperature4 to 38° C
Minimum Sample length180 mm, excluding termination
Wire gauge rangeAWG 20 - AWG 3 (0,8 - 6,4 mm)
Slot widths standard fixture0,8 - 1,3 - 1,5 - 2,0 - 2,3 - 2,8 - 3,3- 3,6 - 4,1 - 4,3 - 4,8 - 5,1 - 5,6 - 6,1 - 6,4 mm
Weight1,2 Kg
Warranty3 years

Related Products

WT3-201 Wire Crimp Pull Tester


  • Measures real-time and peak force values
  • Ergonomic lever operation produces 1.000 N
  • USB, RS-232, Mitutoyo (Digimatic), and analog outputs

More details

WT3-201 Wire Crimp Pull Tester

WT3-201M Motorized Wire Pull Tester


  • Auto-start upon sample insertion
  • Auto-reverse at sample break or load
  • Date / time stamp for all saved data (optional function)

More details

WT3-201M Motorized Wire Pull Tester

F105 / F305 / F505 / F505H Force Test Frame with IntelliMESUR® controls


  • Set up, run, and analyze data via the integrated IntelliMESUR® control panel
  • Integrated motion control and data collection solution with seamless interface for FS05 force sensor without cables
  • Plug & Test® system can work with third-party load cells through PTAF adapter

More details

F105 / F305 / F505 / F505H Force Test Frame with IntelliMESUR® controls

Series-F + EasyMesur F105 / F305 / F505 / F505H Series F test frames with EasyMESUR® F105 / F305 / F505 / F505H


  • Integrated Force sensor and seamless interface for FS05 force sensor without cables
  • Integrated touch screen control panel
  • Set up, run, and analyze data via the integrated EasyMESUR® control panel

More details

Series-F + EasyMesur F105 / F305 / F505 / F505H Series F test frames with EasyMESUR® F105 / F305 / F505 / F505H

Downloads

Buy Now
Product

Product
Price
Quantity
135649
MR06-200 - Force sensor, wire crimp pull testing - 1000 N
€ 1.774,00 
 
Accessories

Product
Price
Quantity
133297
M3I-E -Series 3I Torque/Force Indicator
€ 651,00 
133296
M5I-E -Series 5I Advanced Torque/Force Indicator
€ 988,00 
134266
M7I-E -Series 7I Advanced Torque/Force Indicator
€ 1.677,00 
All mentioned prices are excluding VAT & excluding shipment costs.
Availability: Available: 1 - 3 days, Delivery time: 1 - 3 weeks, special order request

\n